某富含蛇纹石的低品位难选铜镍矿选矿工艺研究

针对某铜镍矿铜镍品位低,铜镍矿物嵌布粒度微细,共生关系复杂,蛇纹石含量高等特征,开展了选矿工艺试验研究。试验结果表明,采用预先脱除脉石-铜镍混合浮选流程,通过对含Ni 0.51%、含Cu 0.20%、含Co 0.02%的原矿进行选择性磨矿,利用MIBC预先脱除部分易浮脉石,碳酸钠作矿浆pH调整剂,CMC作MgO脉石的抑制剂,硫酸铜和丁基黄药分别作铜镍矿物的活化剂和捕收剂,全流程浮选闭路试验获得了含Ni 7.78%、Cu 2.91%、Co 0.24%,回收率分别为Ni 72.98%、Cu 66.57%、Co 51.29%的铜镍混合精矿。该工艺流程获得了较好的选别效果,实现了铜、镍、钴的有效回收。     

镍基MOF电极材料物理超声改性及电化学性能

采用水热法合成了以4,4′-联苯二甲酸(BPDC)为配体的Ni-金属有机框架(MOF),利用低成本、无污染的物理超声法在不改变Ni-MOF晶体结构的前提下对其进行改性,使块状Ni-MOF表面产生孔隙,改善Ni-MOF表面微/纳米结构,提高其电化学性能。通过扫描电子显微镜(SEM)图、X射线衍射(XRD)谱、循环伏安(CV)曲线和恒电流充放电(GCD)曲线分析了改性前后Ni-MOF的微结构形貌和电化学性能。结果表明,经过超声处理后,Ni-MOF的比表面积从40.6 m^2·g^-1增加到65.8 m^2·g^-1,平均孔径从12 nm增加到22 nm。在0.5 A·g^-1电流密度下,超声处理后Ni-MOF电极比电容从420 F·g^-1增加到515 F·g^-1,提高了22.6%,电荷转移电阻明显降低,从25.11Ω降低到15.51Ω。因此,物理超声法可有效改善Ni-MOF表面微/纳米结构,提高其电化学性能。     

原料丙烯中的杂质对聚合反应的影响

就目前来看,聚丙烯主要采用液相本体生产方式,因原料丙烯内含杂质,对生产聚合反应造成一定不良影响的问题日渐凸显。为从根本上提升聚丙烯生产质量与效率,相关研究工作者需对原料丙烯中杂质种类以及对聚合反应的影响进行深入分析,制定出最佳优化方案。     

Thermoluminescence based personnel neutron dosimetry study of LiMgBO3:Dy3+

The present paper reports the thermoluminescence (TL) based personnel neutron dosimetry studies of LiMgBO₃: Dy³⁺ phosphor. It offers the great advantage of being a near tissue equivalent material with Z_eff = 9.1. Also, the presence of both Li and B in the host matrix directly induce TL signal for neutrons. This is highly advantageous over CaSO₄: Dy based TL neutron dosimeters where it requires to mix some thermal neutron sensitive species with the host matrix to induce neutron response. LiMgBO₃: Dy³⁺ was synthesized by sol gel method and its structural characterizations were done by XRD, SEM and EDS techniques. TL upon irradiation with neutrons showed the glow peak at ~140 °C (413K). TL response up to 200 mSv of neutron dose showed very good linearity with adj. R² = 0.998. 30% borated rubber discs were successfully utilised for the segregation of the gamma dose from the total dose in the mixed field (neutron + gamma) environments. The minimum detectable dose of the material was found to be 27.5 μGy and 2.7 μSv for gamma and thermal neutrons respectively. The TL sensitivity of LiMgBO₃: Dy³⁺ for neutron and gamma radiation is 0.6 times and 0.3 times respectively with respect to that of standard TLD-100 [LiF: Mg, Ti] material. The proposed LiMgBO₃:Dy³⁺ was also found to have better n/γ dose discrimination capability as compared to the commercially available TLD-100 material [LiF: Mg, Ti]. The kinetic parameters (viz. E, b and s) of the neutron irradiated TL glow peak were determined by Chen's peak shape and by variable heating rate methods.     

高镁镍渣-磷石膏基复合胶凝材料的制备与性能评价

采用机械研磨的方式将高镁镍渣（HMNS）和磷石膏（PG）筛分至不同粒度，评价了掺不同粒度高镁镍渣和磷石膏复合胶凝材料的力学性能，并对强度形成机制进行了分析。评价了各种配比下浆体的抗压强度和体积稳定性，并分析了其作用机制。试验表明：以HMNS∶PG∶富钙硅质材料ZL=5.4∶3.6∶1配比制得试样的28 d抗压强度为4.43 MPa；室温环境下养护56 d，SP6线性收缩为1.02×10-3 mm/mm，体积稳定性优良；水化产物Ca(OH)2更少，Ca（OH）2与HMNS-PG体系反应生成了CSH凝胶和AFt，结构更为稳定。     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

A next-generation wide color gamut WLED with improved spectral performance in phosphor composite functional solid

As is well known, a way to obtain a high color resolution and saturation of a liquid crystal display and thereby obtain a higher visual accuracy and comfort in the coming 5G era remains an urgent challenge. In the present study, a new type of phosphor composite material doped with Ln³⁺ ions provides a promising alternative to the color filters used in White light-emitting diodes (WLEDs), achieving a better performance regarding the realization of a wider color gamut. The advantages of this composite material are illustrated through an abundant phase and morphology analysis along with a discussion regarding the X-ray photoelectron spectroscopy of the valence bond of Ce ions, which maintain the luminescence properties of the phosphor while providing a stable and solid amorphous environment. An improved spectral performance was obtained through color filtering at 580 nm along with the regulating effects of red, green, and blue emissions according to the doped Ln³⁺ ions. Notably, we fabricated a high-performance WLED based on a Ln³⁺-doped PiG with a correlated color temperature of 5037 K, color rendering index of 72.8, and high color gamut of 91.97%, providing a new choice for the development of luminescence materials with a high color resolution and saturation.     

The influence of sodium caseinate on the physical properties of spray‐dried honey

The aim of this work was to spray dry honey (rape and buckwheat varieties) with Arabic gum (AG) as a carrier alone or in combination with sodium caseinate (1% and 2% w/w NaCas) as a drying aid. Powder recovery ranged from 66.2 ± 0.7% to 75.8 ± 4.9%, and the values were significantly higher for samples containing NaCas. Powders were characterised by good flowability, the addition of NaCas had positive impact on this factor. However, the hygroscopicity of protein‐containing powders was higher, especially at 2% w/w of NaCas. Powders hygroscopicity was related to particle size: AG powder of the smallest particle size was the most hygroscopic, while the particle size did not affected flowability, which was strongly related to the feed solution composition. Based on the obtained results, it was concluded that the addition of 1% w/w of NaCas as a drying aid during buckwheat and rape honey spray drying with Arabic gum as a carrier is favourable, while the further increase of protein content does not give additional benefits.     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

燃煤锅炉除尘专用滤料的开发

介绍机械制造厂燃煤锅炉的烟尘特点,分析滤料失效的原因,提出一套针对该工况的滤料解决方案。介绍针对复杂工况条件所选用的纤维种类以及复合面层原料成分配比的确定,最终选用针刺工艺加工并对该新产品的基本性能进行了测试分析。